Our Work

A Selection of Signature Projects

Exterior Strip & Paint

Powerwashed, scraped, caulked and weatherproofed, board replacement, and 2 coats of paint on trim, body, fascia & soffit.

Walkway & Bed Install

Removed and replaced existing plantings with new design and new mulch, removed concrete walkway, prepped base, filled with compacted gravel, topped with leveled stone dust, pavers installed in straight herringbone pattern and gaps filled with permasand.

Paver Walkway & Landing

Removed existing concrete walkway, filled with compacted gravel, topped with leveled stone dust, pavers installed in straight herringbone pattern, filled gaps with permasand, installed a new 6’ step, veneered sides of landing and risers with natural stone veneer, and installed a granite treads and granite tiles on landing.

Rustic Oak Hardwood Install

Removed existing tile and hardwood floor, removed baseboards, cleaned subfloor, laid paper underlayment, installed 2 ¼” Prefinished Rustic Red Oak, reinstalled baseboards and caulked gaps and nail holes

Exterior Strip & Paint

Powerwashed, scraped, caulked and weatherproofed, board replacement, and 2 coats of paint on trim, body, fascia & soffit.

Walkway

Prepped base – installed and compacted gravel – laid and leveled 1″ of stone dust – installed pavers in straight herringbone pattern – filled joints with permasand

Wall Rebuild

Carefully removed existing retaining wall blocks and caps – dug-out existing base to 3′ – filled base with 3/4″ crushed stone – buried first row of wall block – installed french drain behind wall to prevent wall movement – rebuilt wall

Vinyl Fence Install

Cut back existing hedge line, Installed 6’ white vinyl fence with poles buried 3’ under ground and filled with concrete, and installed decorative rocks.

Retaining Wall Install

Removed existing wall, prepped 3’ base, filled base with ¾” crushed stone, buried first row of wall block below driveway level, installed French drain behind wall, built up wall and glued on cap.

Tile Floor Install

Removed existing engineered flooring, prep and level subfloor, lay tile with leveling system, grout and seal.

Select Maple Floor Install

Removed existing tile and carpet, removed baseboards, prepped subfloor, laid paper underlayment, installed 3 ¼” Prefinished Select grade Maple, reinstalled baseboards, caulked gaps and filled nail holes.

Interior Painting & Laminate Floor Install

Wiped down walls, caulk gaps, filled nail holes, painted ceilings, painted trim and walls with 2 coats, and installed new laminate floor in kitchen and living room.

Maple Hardwood Floor Refinish

Sanded floor with 40 grit – sanded with 80 grit – buffed with 150 Screen – applied 3 coats of poly – buffed with 220 screen after first and second coat – cleaned thoroughly after each sanding and buffing

Before

Prep

After

Interior Painting & Hardwood Install

Removed carpet and baseboards – removed electrical plates – filled nail holes – caulked gap, where trim meets wall – painted ceiling, walls, and trim with 2 coats – painted baseboards, when detached from the walls – laid paper underlayment – installed prefinished 2 ¼” red oak, leaving ¼” gap on all walls – nailed floor every 6” with 2” staples – reinstalled baseboards – caulked gaps – filled nail holes – touched-up baseboards

Before

Prep

After

Tile Floor Install

Removed existing tile that was laid over radiant heat system – removed step-up to breakfast bar – cleaned concrete subfloor thoroughly and carefully as to not damage heating system – installed new porcelain tile using leveling system to aid in levelness – grouted tile – sealed grout

Before

Prep

After

Walkway & Step Install

Prepped and dug out base – installed and compacted gravel – topped gravel with 1” of leveled stone dust – installed 6 granite steps – laid pavers in straight herringbone pattern – spread permasand in all joints

Before

Prep

After

Walkway Install

Prepped and dug out base – installed and compacted gravel – topped gravel with 1” of leveled stone dust – laid pavers in straight herringbone pattern – spread permasand in all joints

Before

Prep

After

Maple Hardwood Floor Install

Removed carpet and existing hardwood – installed and leveled new ¾” plywood subfloor – laid paper underlayment – installed prefinished 3 ¼” Select Maple, leaving ¼” gap on all walls nailing floor every 6” with 2” staples – installed new prefinished oak baseboards – filled nail holes with oak putty

Before

Prep

After

Laminate Floor Install

Removed carpet and baseboards – prepped and cleaned subfloor – installed pre-padded laminate, leaving a ¼” gap on all walls – reinstalled baseboards – caulked gaps – filled nail holes – installed a t-molding, where tile meets new laminate floor

Before

Prep

After

Walkway Install

Prepped and dug out base – installed and compacted gravel – topped gravel with 1” of leveled stone dust – laid pavers in traditional herringbone pattern, with clight curves (customers choice) – spread permasand in all joints

Before

Prep

After

Tile Stair Install

Removed existing stair tile – prepped and clean treads and risers – installed new porcelain tile, using leveling system – grouted tile – sealed grout

Before

Prep

After

Hardwood Stairs Install

Removed existing carpet – cut lips of stair treads – installed prefinished oak stair treads, using wood glue and 2” finish nails – filled nail holes with oak wood putty – installed primed white risers – painted risers to match trim color

Before

Prep

After

Outdoor Deck Refinish

Power washed deck – sanded down deck to remove debris and peeling stain – stained deck with 2 coats of soild stain

Before

Prep

After